Differences

This shows you the differences between two versions of the page.

--- en:edu:zmitac:s2:aih:lab:stm32fan [2024/01/13 19:49] – ktokarz
+++ en:edu:zmitac:s2:aih:lab:stm32fan [2024/01/16 09:37] (current) – ktokarz
@@ Line 8: / Line 8: @@
 </table>
 In the stm32duino examples ((https://github.com/stm32duino)), there is a simple program which allows us to control a single LED with PWM. It is named "All-in-one_setPWM" ((https://github.com/stm32duino/STM32Examples/tree/main/examples/Peripherals/HardwareTimer/All-in-one_setPWM)). It uses hardware timer output connected directly to an LED. We will modify this example to control the fan and servo.
-The code is composed of two files FanSrvTest.h and FanSrvTest.cpp. The *.h file defines pins for the fan and servo, declares variables for timer, channels and
+At the beginning of the code, we need to define pins.
-<code>
+<code c>
-#include "Arduino.h"
-#ifndef _SRV_TestLib
-#define _SRV_TestLib
 // PWM timer 2 for Servo and Fan control
 #define SERVO_PWM_PIN PA0
 #define FAN_PWM_PIN PA1
+</code>
+<note>
+Pin names use STM naming, not Arduino naming.
+</note>
+Both outputs are controlled with the same timer, so only one instance of the timer is needed. It will control two channels one for fan, one for servo.
+<code c>
 // PWM variables definitions
 TIM_TypeDef *SRVInstance;        //General hardware instance
 uint32_t channelSRV, channelFAN; //2 channels
 HardwareTimer *MyTimServo;       //Hardware Timer class for Fan and Servo PWM
-//Prototypes of funcions
-void FanSrvSetup();
-void fFanSet(int pPercent);      //Change the fan speed (0-100)
-void fSrvSet(int pAngle);        //Change the servo angle (0-180)
-#endif
 </code>
+At the beginning of the code timer object must be created and two channels activated. Notice that because there is one timer, the base frequency for the fan and servo is the same. Certainly, the duty cycle can be different.
+<note>
+The frequency used must fulfil the requirements of the servo. The one used in the laboratory stand requires a PWM signal with a pulse sent every 20ms (50Hz). The duty cycle can vary between 500us (microseconds) and 1500us, where 1000us gives 90 degrees of the angle.
+</note>
+<code c>
+  //Create Timer instance type based on the servo pin (the same timer is used for fan).
+  TIM_TypeDef *SRVInstance = (TIM_TypeDef *)pinmap_peripheral(digitalPinToPinName(SERVO_PWM_PIN), PinMap_PWM);
+  //Define two separate channels for servo and fan
+  channelSRV = STM_PIN_CHANNEL(pinmap_function(digitalPinToPinName(SERVO_PWM_PIN), PinMap_PWM));
+  channelFAN = STM_PIN_CHANNEL(pinmap_function(digitalPinToPinName(FAN_PWM_PIN), PinMap_PWM));
+  // Instantiate HardwareTimer object. Thanks to 'new' instantiation, HardwareTimer is not destructed when setup() function is finished.
+  MyTimServo = new HardwareTimer(SRVInstance);
+  // Configure and start PWM
+  MyTimServo->setPWM(channelSRV,SERVO_PWM_PIN,50,5); // 50 Hertz, 5% dutycycle.
+  MyTimServo->setPWM(channelFAN,FAN_PWM_PIN,50,50);   // 50 Hertz, 50% dutycycle.
+</code>
+To modify the duty cycle it is possible to use the function setCaptureCompare() which has the possibility of passing the argument as the value of microseconds or percents. The following lines show examples of setting that fan speed in percents (provided by FanSpeed variable), and servo range in duty cycle time (provided by SrvTime variable).
+<code c>
+  MyTimServo->setCaptureCompare(channelFAN, FanSpeed, PERCENT_COMPARE_FORMAT);
+  MyTimServo->setCaptureCompare(channelSRV, SrvTime, MICROSEC_COMPARE_FORMAT);
+</code>