Differences

This shows you the differences between two versions of the page.

--- en:edu:zmitac:s2:aih:lab:nrf52gpiote [2023/11/22 20:01] – ktokarz
+++ en:edu:zmitac:s2:aih:lab:nrf52gpiote [2023/12/01 13:51] (current) – ktokarz
@@ Line 1: / Line 1: @@
 ====== Programmable Peripheral Interconnect ======
-PPI is used
+Programmable Peripheral Interconnect (PPI) is the matrix that creates programmable connections between the internal peripherals of the microcontroller. It is possible to connect output signals from peripherals known as EVENTS with inputs of other peripherals known as TASKS. It is possible to connect the input and output of the same peripheral creating so-called SHORTCUT. PPI is used to create direct connections that transmit control signals without the need for program execution.
-The second part of the laboratory shows how to use the PPI to send the activation information from the button (sw0) directly to the LED (led0). It is possible to set up the hardware connection between the button EVENT signal and the TASK signal for LED. While the output is controlled by the GPIOTE mechanism the normal GPIO writes have no effect. The GPIOTE mechanism is not supported in Zephyr OS, but the driver (NRFX) which is provided directly by Nordic Semiconductor can be used in Zephyr-compatible software.
-The example provided uses the GPIOTE (GPIO Tasks and Events) to handle signalling. To make it work properly the config file must be changed, enabling the NRFX driver:
-CONFIG_NRFX_GPIOTE=y
+===== Using PPI with GPIO =====
-There is a need to disable the general GPIO driver:
+This part of the laboratory shows how to use the PPI to send the activation information from the button (sw0) directly to the LED (led0). It is possible to set up the hardware connection between the button EVENT signal and the TASK signal for LED. While the output is controlled by the GPIOTE (GPIO Tasks and Events) mechanism the normal GPIO writes have no effect. The GPIOTE mechanism is not supported in Zephyr OS, but the driver (NRFX) which is provided directly by Nordic Semiconductor can be used in Zephyr-compatible software. Every connection between EVENT and TASK is done by defining the channel. The number of available channels is limited to 8.
+The example provided uses the GPIOTE to handle signalling. To make it work properly the config file must be changed, enabling the NRFX driver, and disabling the general GPIO driver:
+<code>
+CONFIG_NRFX_GPIOTE=y
 CONFIG_GPIO=n
+</code>
 Additionally, we can use the logging mechanism to receive log messages from the software. To do this we enable logging with:
+<code>
 CONFIG_LOG=y
+</code>
 The resulting config file prj.conf looks like this:
+<code>
 CONFIG_GPIO=n
 CONFIG_SERIAL=y
 CONFIG_NRFX_GPIOTE=y
 CONFIG_LOG=y
-To do the second part of the laboratory take the following steps:
+</code>
-Modify the prj.conf file.
-Replace main.c with the code included below.
-Modify the code to turn the LED on with one button, and off with another button.
-To make point 3 of the exercise it is essential to know that one GPIO can have three TASK signals:
-SET - to write the high state
-CLEAR - to write the low state
-OUT - to specify behaviour in the configuration (set, clear or toggle).
-The example provided uses the OUT TASK with toggle configuration. There is no need to configure SET or CLEAR tasks, but there is a need to create separate PPI channels, one for setting LED with one button, and another for clearing it with a second button.
-While creating channels you can use the functions for resolving the TASKs handlers addresses:
+===== Tasks to be done during the laboratory =====
+To do this part of the laboratory take the following steps:
+  - Modify the prj.conf file.
+  - Replace main.c with the code included below.
+  - Modify the code to turn the LED on with one button, and off with another button.
+To make point 3 of the exercise it is essential to know that one GPIO can have three TASK signals:
+  * SET - to write the high state
+  * CLEAR - to write the low state
+  * OUT - to specify behaviour in the configuration (set, clear or toggle).
+The example provided uses the OUT task only with toggle configuration. In the exercise, while replacing the OUT task with SET and CLEAR there is no need to configure such tasks, but there is a need to create separate PPI channels, one for setting LED with one button, and another for clearing it with a second button.
+While creating channels you can use the functions for resolving the TASK's handlers addresses:
+<code>
 nrfx_gpiote_set_task_addr_get();
 nrfx_gpiote_clr_task_addr_get();
+</code>
 The initial, unmodified code of the main.c file looks like this:
+<code>
 /*
  * Copyright (c) 2019 Nordic Semiconductor ASA
@@ Line 178: / Line 188: @@
     LOG_INF("(D)PPI configured, leaving main() %d", 0);
 }
+</code>